Electrostatic protection
Assemble a bonded handling station and verify surface/personnel/packaging discharge paths before handling sensitive devices Discovery hypothesis; acceptance remains open.
Discovered · unresearchedClosure: BlockedInventory incomplete
Capability requirements and tolerances
Consumer-specific numerical targets, quantities and acceptance limits remain open or incompletely reviewed. No smartphone-grade suitability is claimed. Distinct capability tiers require their own making route and qualification.
Making steps · draft selected for navigation; not a validated fabrication specification.
Known Parts and Tools
The selected route supplies this page's inventory and the map's dependency links from one record. Further requirements may be missing; review flags do not prove physical suitability.
| Requirement | Role | Use | Relationship status |
|---|---|---|---|
| Dissipative work mat | Tool | reused during construction/verification | Cycle-checked; compatibility unknown |
| Personnel grounding band | Tool | reused during construction/verification | Cycle-checked; compatibility unknown |
| Grounding leads | Part | incorporated or consumed; allocation remains open | Cycle-checked; compatibility unknown |
| Static protective container | Tool | reused during construction/verification | Cycle-checked; compatibility unknown |
| Electrical instruments | Tool | reused during construction/verification | Cycle-checked; compatibility unknown |
| Insulation test instrument | Tool | reused during construction/verification | Cycle-checked; compatibility unknown |
| Power distribution | Tool | reused during construction/verification | Cycle-checked; compatibility unknown |
| Workshop surfaces | Tool | reused during construction/verification | Cycle-checked; compatibility unknown |
Making outline
- Assemble a bonded handling station and verify surface/personnel/packaging discharge paths before handling sensitive devices
- Build or acquire each explicit earlier physical input; establish independent references and interfaces.
- Make trials and accept only against the eventual caller specification; record uncertainty and rejected outputs.
What remains unresolved
- Identified requirement; no researched making route or qualified output yet.
- Full inventory, required quantities, process settings, numerical demand and suitability remain open.
Sources and leads
Source scope and research notes determine which claims have been checked. A URL does not establish a complete making route.
Earlier research provenance
- proposals/2026-10-08-discovery/electronics/frontier-report.md
Used by
Items that directly require this item in their selected inventory.
- Accelerometer
- Acoustic acquisition interface
- Acoustic test equipment
- Actinic radiant comparison reference
- Assembly equipment
- Audio amplifier
- Audio codec
- Audio codec die
- Audio signal source
- Battery current-sense shunt
- Battery disconnect switch assembly
- Battery protection electronics
- Battery protection threshold comparator assembly
- Battery temperature-sense element
- Battery validation
- Calorimeter RF reference absorber
- Calorimeter thermopile assembly
- Charging control
- Charging controller die
- Chip packaging equipment
- Chip resistors
- Chip test equipment
- CMOS image sensor die
- Coaxial open impedance standard
- Coaxial resistive load standard
- Coaxial RF microcalorimeter core
- Coaxial short impedance standard
- Coherent quadrature mixer core
- Component-placement system
- Control clock assembly
- Control electronics
- Control input output assembly
- Control logic assembly
- Control memory assembly
- Directional coupled-line core
- DRAM die
- Electrical inspection instruments
- Exposure equipment
- Fingerprint sensor if selected
- Formation cycler
- Glass dynamic edge impact stage
- Glass four-point bend stage
- Glass stress profile instrument
- Gyroscope
- Hall magnetic sensor die
- Handset audio amplifier
- Handset audio amplifier die
- Haptic actuator
- Haptic driver die
- Hardwired electrical inspection harness
- Image sensor
- Instrument coaxial connector
- Instrument RF band filter set
- Instrument RF LC oscillator bank
- Instrument RF output attenuator
- Light sensor
- Loading contact fixture
- Low noise amplifier die
- Low noise radio amplifiers
- Magnetometer
- Main board
- Manual DUV projection control panel
- Measurement microphone
- Memory
- Microfocus X-ray source assembly
- Microphone
- Modem and baseband
- Modem die
- Motion sensor
- NAND flash die
- NFC interface
- Optical inspection instruments
- PCB contact exposure fixture
- PCB drill and routing module
- PCB lamination press module
- PCB manual coordinate control apparatus
- Photodiode die
- Power management
- Power management die
- Processor
- Processor die
- Programming fixture
- Programming tools
- Proximity sensor
- Radiation survey instrument
- Radio acoustic filter die
- Radio directional bridge
- Radio measurement receiver
- Radio power amplifier die
- Radio power calibration reference
- Radio power detector
- Radio reference oscillator
- Radio switch die
- Radio switches
- Radio test signal source
- Radio transceiver
- Radio transceiver die
- Receiver IF and phase readout chain
- Resist coating equipment
- RF detector DC substitution bridge
- RF frequency comparison station
- RF front end
- RF phase transfer fixture
- RF thermal power sensor mount
- Satellite navigation receiver
- Sensor readout die
- SIM and eSIM handling
- SIM secure element die
- Smartphone
- Storage
- Storage controller die
- Touch controller
- USB controller die
- USB interface control
- WiFi and Bluetooth module
- Workshop computer
- X-ray high voltage supply assembly
- X-ray independent interlock chain
- X-ray scintillator optical detector assembly
Paths from Smartphone
These routes together include every item that can lead from Smartphone to this item. Repeated path combinations are collapsed; recipes are omitted.
Shortest route: Smartphone → Electrostatic protection
Enable JavaScript to see the routes covering every contributing item.